Buy Guitar Bridges

Quality guitar hardware from MGB Guitars. Perfect for homemade instruments. Reminiscent of the Frisco bridge that spans the Mississippi at Memphis. At .6 inches this bridge is taller than most but can be cut or sanded to the right height.  String location notches are provided along the top edge. 3 string slots are spaced .5 inches apart and 4 string are .4 inches. Make sure to file the slots to provide a back angle falling off toward the tailpiece.  2 3/4 Inches wide and .6 inch tall. Easily sanded to get the right height. Light sanding required, suitable for staining or painting

Quality guitar hardware from MGB Guitars. Maple and Rosewood construction Comes with six shallow slots Easily modified to work with any string configuration  3 1/8" by 1/4"

Chrome four string wrap around bridge suitable for cbg builds. Saddles are spaced .6 inches apart and string width at bridge is 1.8 inches. Requires a larger than standard neck, one that is close to 2 inches and the box end.  These bridges are taller than standard bridges requiring the the stagger between the box face and fret height to be near .5 inches. The mounting post allow for fine adjustment to get the action height correct. Template is included for laying out mounting hole locations. Simply line up the template on the centerline an scale length. Mark the holes and drill with a 12mm drill bit. You can use a smaller bit and file to size. Add backer to make sure top is close to .750 inches thick at the hole position.

Four pack of single shot bridges for bass guitar Chrome or black finish Allows flexible string spacing

Floating bridge with cable Piezo and Saddle. Works with guitars, ukuleles and other instruments Includes cable piezo Works perfectly with MGB Preamp/Tuner Available in Maple or Cherry Genuine bone saddle Made for 2,3 or 4 string instruments

Available in 3 and 4 string models, these new MGB Pitch Benders can add a new dimension to your CBGs. Includes all of the chrome finished components and hardware needed. Also includes a template to provide accurate location and sizing of hole for the bridge and locations for mounting screws. Critical steps for installation: Use the template (included) for accurate lay-out of holes. Make sure to line up the box center line and scale length line.  Secure anchor block (2 1/2 x 4  inches) to inside of lid. It should meet with edge of hole. The bridge screws will need to go through the lid and into the block. Do not over tighten screws that secure the bridge. The bridge must lay flat against the box, see pic. The bridge will need to pivot to shorten the strings and bend the pitch. Anchor the springs to provide tension, you can use the spring bracket or install screws in the anchor block. Our experience shows that stretching the strings about 1/2 inch from the normal state provides the right tension. This tension will will keep the bridge flat and allow tuning. Bending the bar will further stretch the springs and allow the bridge to pivot. The 3 string uses two springs and the 4 string uses three springs. The strings are bottom loading so access through the back of the box is needed.

Two pack of Rosewood thumb rests. 2 1/2 by 1/2 by 1/2 inches Mounting Screws included  

This floating Rosewood bridge allows total flexibility in bridge placement. Dimensions are 3 1/2 by 1 1/8 inches and .35 inches tall. The length of the fret wire is 2.4, Suitable for 3,4 and 6 string builds. Can be easily glued in place once optimal location is determined.

Walnut Adjustable 8 strings Compensated

6-string Antique Brass hard-tail bridge perfect for electric guitars. Top-loading. Sturdy metal construction, bright mirror-like gold finish. Mounting screws and allen wrench included. Individually adjustable string saddles allow exact intonation adjustments 6-string Antique Brass hard-tail bridge perfect for electric guitars. Top-loading. Sturdy metal construction. Chrome mounting screws and allen wrench included. Individually adjustable string saddles allow exact intonation adjustments Also available in Chrome Gold and Black finishes. Easy Bridge Placement Template HERE  

This bridge riser is intended for use with 4 string hardtail bridges. This allows for furthering the height of the string on your build!

Traditional 3 string bridges have a narrow 12 mm spacing between strings. This places the strings close together and can can be challenging for players with bigger hands and fingers. The new MGB XL bridge solves that problem providing a bridge with ample spacing. The spacing between strings on the new XL Bridge is 16mm (0.625", just under 5/8") with total distance from string 1 to string 3 being 32mm or 1.25 inches which works perfectly with a 1 1/2 inch neck. This bridge is a "top-loading" style, which means that the strings are fed through the back plate of the bridge, then up and over the saddles. No drilling through the instrument/box is required  Each one is mounted securely by four screws, and a small hex wrench is also included for adjusting the small set screws that control string action height. The saddles can be adjusted by means of a screw at the back of the bridge to get the intonation just right, and small set screws at the front of each saddle let you set the string action height.  Perfect for 3-string cigar box guitars Sturdy metal construction Chrome, Black, Gold or Antique Brass finish Individually adjustable string saddles Mounting screws and wrench included Top-loading  Find XL Bridge shim HERE Easy Bridge Placement Template HERE E-System Bridge Locator Template HERE

Quality guitar hardware from MGB Guitars. Perfect for homemade instruments.  String location notches are provided along the top edge. 3 string slots are spaced .5 inches apart and 4 string are .4 inches. Make sure to file the slots to provide a back angle falling off toward the tailpiece.  3 1/2 Inches wide and 1/2 inch tall. Easily sanded to get the right height. Light sanding required, suitable for staining or painting

New from MGB, a quick and easy way to precisely position the bridge on your next build. This template will all allow you to mark the proper locations for the mounting holes on your bridge onto the box. It works with standard 3,4 and 6 string bridges. It will also work with MGB 3 string XL bridges.  First mark your box with a centerline then a  line for the scale length. Position the template on over these lines. Drill the appropriate holes along with the ground wire hole. 

This template allows the builder to accurately locate any of the MGB Flat Pups and mark the necessary holes for mounting the cover. it easy to use, simply: I identify and mark the centerline of the box. Select the appropriate pickup on the template. Mark the mounting holes and the wire hole for the pickup. Drill a one inch hole when using a RSG pickup where the pickup is already soldered to a harness.  Install the pickup/cover. The template provides the name and part number of all MGB Flat Pups and the cover options.

Quality guitar hardware from MGB Guitars. Perfect for homemade instruments. Reminiscent of the Frisco bridge that spans the Mississippi at Memphis. At .6 inches this bridge is taller than most but can be cut or sanded to the right height.  String location notches are provided along the top edge. 3 string slots are spaced .5 inches apart and 4 string are .4 inches. Make sure to file the slots to provide a back angle falling off toward the tailpiece.  2 3/4 Inches wide and .6 inch tall. Easily sanded to get the right height. Light sanding required, suitable for staining or painting

MGB is pleased to announce our latest template, this template will aid in locating our Tele Style bridges. Precise location of these bridges is critical in making a cbg that will be easy to tune and intonate. It will also aid in getting the strings properly located/centered in relation to the fret board. This template works with our Easy Neck, Super Neck and Super Sixer Neck. It works with our 3 String XL bridges, 4 String Bridges and our 6 String Bridges.  Using the E-System is easy. Mark the center line of the box. We suggest using Blue tape and a pencil or pen Position the body of the template on the box lining it up with the center line and the neck end of the box.  Temporarily secure the template with Blue tape. Each insert is marked with the neck/bridge combination that it is meant to work with. Select the appropriate template insert that matches the neck and bridge you are using. Before attaching the bridge to the box do a dry fit and make sure the distance from the nut to leading edge of the saddles corresponds to the sale length. This is a critical step, always confirm that the location of the bridge is correct before drilling and installing screws.

Traditional 3 string bridges have a narrow 12 mm spacing between strings. This places the strings close together and can can be challenging for players with bigger hands and fingers. The new MGB XL bridge solves that problem providing a bridge with ample spacing. The spacing between strings on the new XL Bridge is 16mm (0.625", just under 5/8") with total distance from string 1 to string 3 being 32mm or 1.25 inches which works perfectly with a 1 1/2 inch neck. This bridge is a "top-loading" style, which means that the strings are fed through the back plate of the bridge, then up and over the saddles. No drilling through the instrument/box is required  Each one is mounted securely by four screws, and a small hex wrench is also included for adjusting the small set screws that control string action height. The saddles can be adjusted by means of a screw at the back of the bridge to get the intonation just right, and small set screws at the front of each saddle let you set the string action height.  Perfect for 3-string cigar box guitars Sturdy metal construction Chrome, Black, Gold or Antique Brass finish Individually adjustable string saddles Mounting screws and wrench included Top-loading  Find XL Bridge shim HERE Easy Bridge Placement Template HERE E-System Bridge Locator Template HERE