MGB

Stainless Steel Highly Polished

Available in chrome, black and gold these ferrules are used to guide and anchor strings. The measure .36" long and .36 wide at the top flange, the knurled center measures .29". Use a 5/16" drill to make a hole. Press the ferrule into the hole and use a small amount of glue if desired. 12 ferrules are provided in a poly bag.

This template is helpful for locating the bridge when using a Super Sixer bolt on neck. Always check to confirm 25.5 inch distance from the fret side edge of the nut to front the edge of saddle.

Perfect for securing strings to the end of the box. Available in Rosewood or Maple Approximately 1/4 inch thick Available in 3 or 4 string Hardware included

MGB presents our new Tele style necks. These professional grade necks are perfect for your next 6 string build. North American Maple Neck Optional roasted Maple available Satin poly finish Rosewood Fretboard 22 Frets 18 inch radius 25.5 inch scale length Pre slotted bone nut installed Face and side fret markers Truss rod uses 4mm hex wrench included Predrilled (10mm) for 6 inline tuners Marking templates included Digital file of the pocket shape is available no charge

A very handy tool for testing components. You can connect the leads on your pickup directly to your amp. You can also use the alligator clips to make additional connections.

Kit includes everything needed to complete this attractive 3 string instrument. Available in three or four string. Available in chrome, black or antique brass finishes.  Included are: 10" x 6.5" x 2.5"  colorful box that is fully machined, reinforced and ready for assembly. 24 inch scale Okume and Maple fretted neck predrilled for three tuners. Neck reinforcement plate is included. String slots on nut are filed but may require minimal adjustments after assembly. Powered by an MGB 750 pickup. Pickup is pre-soldered to harness and ready for easy assembly. Includes tuners, knobs and strap pins, Includes a jack plate and back cover plate. Includes a 3 pack of .013, .017 and .026 strings. Use a 7/16" socket or wrench to tighten hanger bolt and and 10 mm socket or wrench to tighten tuner ferules.     

Kit includes everything needed to complete this attractive 4 string instrument. Available in three or four string. Available in chrome, black or antique brass finishes.  Included are: 10" x 6.5" x 2.5"  colorful box that is fully machined, reinforced and ready for assembly. 24 inch scale Okume and Maple fretted neck predrilled for four tuners. Neck reinforcement plate is included. String slots on nut are filed but may require minimal adjustments after assembly. Powered by an MGB 750 pickup. Pickup is pre-soldered to harness and ready for easy installation. Includes tuners, knobs and strap pins, Includes a jack plate and back cover plate. Includes a 3 pack of .013, .017 .026 and .036 strings. Use a 7/16" socket or wrench to tighten hanger bolt and and 10 mm socket or wrench to tighten tuner ferules.     

Two way action can correct either a backbow or upbow on a neck.  Twin steel rods and brass threaded blocks allow for precise adjustments to get the perfect alignment on the neck. 4mm hex wrench included. We suggest creating a slot about .25 inches wide .5 inches deep in the neck. Make sure the slot is deep enough so that fretboard does not rest on the brass nuts. Also use a dab of E6000 or silicone caulk under each nut to prevent them from moving, do not glue the rods. The slot should be long enough to conceal the adjustment nut under the neck and/or nut.

3 ply black with white center.  Screws included Two Pack

Neck only includes bone nuts and hardware Okume body and Walnut fretboard 20 inch scale with frets installed Fretboard is 12 inches long with 2 inch overhang Heel is 2 inches tall Two bone nuts are provided, one blank and one cut for poly stings Uses 10mm socket item 24008 Works with MGB tuners item 25105

Polyurethane strings for U Bass instruments.  Strings measure .196, .165, .117 and .093 and 32 inches long.

This kit does include a box. This kit includes all the items needed to build a 20 (see note below on intonation) inch scale electric U-Bass. The neck is made of Okume and the fret board and bridge are made of Walnut. The boxes are made from Sapele and well reinforced for this application. Polyurethane strings are provided as well as a bone nut that is fitted to the strings. The neck includes a preinstalled hanger bolt for mounting to the box.  The heavy duty tuners are made specifically for this type of instrument. Unlike other tuners  you will need to disassemble the tuner to install it in head stock. Remove the screw, gear and axle before installing the tuner body. Reassemble and and add washer and ferrule. Tighten with a 15mm wrench. Normal string winders will not work and we suggest you use our 24010 winder which will accommodate the oversized knobs on these tuners. Due to the mass and size of the strings we have found that a scale length of 20.3 inches works better for intonation. The strings are anchored on the bridge using knots on the inside of the box. The bridge can be glued to the box however we prefer using screws and finish washers.  The electronics package includes a compensated piezo pickup, preamp/equalizer, tuner and battery box.  Openings for the preamp and battery box are included. The battery box uses two 2032 (not included) round batteries which are installed positive side up. A plug will need to be installed in the jack for the tuner to operate. Tune to EADG. Special note: As the strings are soft and the leading edge of the nut is quite sharp, oftentimes the strings will bind on the nut and the gears will grind till they fail. The solution is to lift the strings over the nut as you tighten the tuners   If you need help feel free to call Eric at 727 212 7221   Check online for videos on installing U-Bass strings. 

This kit does not include a box. This kit includes all the items needed to build a 20 (see note below on intonation) inch scale electric U-Bass. The neck is made of Okume and the fret board and bridge are made of Walnut. Polyurethane strings are provided as well as a bone nut that is fitted to the strings. The neck includes a hanger bolt for mounting to the box. The minimum box length that can be used is 12 inches and a box that is 13 inches or longer is recommended. Make sure to reinforce the box and we suggest using a 27093 reinforcement plate. The heavy duty tuners are made specifically for this type of instrument. Unlike other tuners  you will need to disassemble the tuner to install it in head stock. Remove the screw, gear and axle before installing the tuner body. Reassemble and and add washer and ferrule. Tighten with a 15mm wrench. Normal string winders will not work and we suggest you use our 24010 winder which will accommodate the oversized knobs on these tuners. Due to the mass and size of the strings we have found that a scale length of 20.3 inches works better for intonation. The strings are anchored on the bridge using knots on the inside of the box. Our 41003 template is available for aligning and positioning the bridge. The bridge can be glued to the box however we prefer using screws and finish washers. When the bridge is installed the string clearance holes can be drilled through the box top. The electronics package includes a compensated piezo pickup, preamp/equalizer, tuner and battery box.  Included are template/trim rings for mounting the components. The battery box uses two 2032 (not included) round batteries which are installed positive side up. A plug will need to be installed in the jack for the tuner to operate. Tune to EADG. Special note: As the strings are soft and the leading edge of the nut is quite sharp, oftentimes the strings will bind on the nut and the gears will grind till they fail. The solution is to lift the strings over the nut as you tighten the tuners.    Check online for videos on installing U-Bass strings. 

High quality padded ukulele carry bag. Heavy padded Cordura construction Waterproof and dust proof Front panel pocket Carry handle and back pack straps 24 x 9 x 3 inches Sized for Concert Ukuleles and smaller instruments

Perfect for keeping strings aligned when using a zero fret. Available in Cherry, Maple or Rosewood. 1.5" wide, .3 " tall and .2 inches thick. Remove mask on Cherry and Maple before gluing in place. Make sure strings rest firmly on the zero fret, adjust slots if need be.